Leecraft Dw-2 Zero-clearance Dewalt Table Saw

Leecraft DW-2 Zero-Clearance DeWalt Table Saw Insert: Fits Many Dewalt models: Fits Dewalt: DW746 DW744 DW745 DWE7480 DWE7490X DWE7491RS DWE7499GD
Fits DeWALT: DW744 & DW745 Portables (factory splitter/guard incompatible with DW-2 insert on these saws) & DW746 (Stationary Saw), DWE7480, DWE7490X, DWE7491RS, DWE-7492QS & DWE7499GD. NOTE FROM THE MANUFACTURER : The old models DW744 & DW745 (portable saws) cannot use factory SPLITTER with DW-2 insert. The required slot (all the way out the back end of the insert) nearly cuts the insert in two, rendering it springy, weak, and unsafe. Think of an old fashioned wooden clothes pin… only held together at one end, and the “legs” can easily be flexed apart or towards each other. Works great for holding clothes on a line, but the opposite of what’s needed for a table saw insert, where you need structural integrity and stability. These are great applications for the This may also apply to the DW746, which was a larger contractor type saw with cast iron table; same splitter design. The newer models (all the others) employ a RIVING KNIFE, which allows for a shorter slot, and a structural “bridge” to remain at the back end of the insert. Obviously, the plate becomes weaker and weaker, the smaller this bridge is, as the RK slot gets closer to the edge. The riving knife (RK) slot is essentially an extension of the blade slot, or kerf. The kerf is, of course, created by simply raising the blade through the blank insert, to the maximum elevation. The operator must then extend the kerf (slot) by means of a secondary procedure, to safely create a slot that sufficiently clears the RK. This “secondary procedure” requires a higher level of understanding, skill, and creativity.
Use MicroJig MJ Splitter Kits
for added table saw safety.  Available in THICK
or THIN
kerf they are easily installed and simple to align.  Not for use with Leecraft inserts that already have the riving knife slot cut in.  Intended for inserts WITHOUT the riving knife slot. INSTALLING AND FITTING YOUR INSERT

Lower the blade completely.

Place insert in table with finger hole at front and starter pocket located over blade.

Run leveling screws down until insert is stable and flush with table top.

Back out side adjustment screw, then front end adjustment screw to achieve a fit that is snug, yet removable.

SPLITTER: 

DW744:

 This insert 

CAN NOT

 be used with the factory splitter. We recommend purchasing (call for sources) or making a pin or blade type splitter which is mounted to the insert itself, just behind the blade slot.  

DW746:

 To use factory splitter, you'll need to cut a short slot at the rear of the insert to accommodate it, using a bandsaw or hacksaw. Leave the "bridge" between the splitter slot and the blade slot as thick as possible.

CUTTING THE BLADE SLOT (KERF)

Check that insert is fitted properly, and that blade is clear. Using a stick, reach under the table and rotate the blade manually to check for blade clearance.

Fully cover the insert with a board, and clamp at each end to the table saw top.

Re-connect power to saw. Switch on, slowly and cautiously raise blade up, to cut its way through the insert. KEEP HANDS OFF OF TABLE TOP, STAY CLEAR AND WEAR GOGGLES. Raise blade to maximum height at this time.

Lower blade, turn off saw, and remove board. Your insert is now ready for use!

IMPORTANT TIPS FOR USE

Only recommended for use with carbide tipped cutters.

DADO BLADE - Use same procedures outlined above, but use additional caution due to excessive material being machined from insert during the slotting procedure.

Under certain conditions, an undesirable scraping noise may be generated by your saw blade. Planer type blades and/or excessive arbor run-out, and/or blade distortion, may be causing intermittent contact with the insert slot. To remedy this, remove the insert and slightly widen the slot using a file or sanding paddle.

Ideally, a separate insert should be used with each blade, dado stack, or angle set-up. This will insure a true "zero-clearance" effect and give you maximum benefit from your inserts.

Features
Details

Shipping Weight: 0.0 pounds

Item MPN: DW-2

Fast Shipping at the Lowest Prices!
Order are packed the following day they are recieved in most cases! Orders placed on Friday during the day will be shipped out Monday. We've tried our best to advertise honest, fair, and low-cost shipping. This includes the ability to combine shipping on orders from our store. If you feel as though the shipping charge or the combined shipping charge is too high, please contact us with your concerns in order to get you the best agreed upon price! If you'd like expedited shipping, and it is not available, please reach out directly!
Competitive FLEXIBLE Pricing!
With our dynamic pricing model, our prices are always competitive. If you have a question or would like to discuss pricing more, reach out directly! Offers are more than welcome even if not available through listing, just send a message and let us know of your interest!
30-day Money Back Guarantee
We are committed to making sure that you leave this transaction satisfied. If you're unhappy with the product for any reason, you may return it back for your money-back. Please see specific return policy relevant to the item your viewing! (Original shipping costs will not be refunded in most cases)

Returns Accepted for this item if it's within 30 Days